Martech BOX III new product
Hello!
On 02.04.2014 we introduce our new product - Martech Box III.
Why a new Box ? You can read here:
About | Martech Box3 Help
What's new in Box III, which is not on Clip so far:
- Nissan LCN / Opel Corsa Touch & Connect (within the activation OMAP5948) original code reading
- full support (read, write, erase) of M35080 3/6/V6/VP/D80/D160 (under the tab of programmer)
- new user interface - easier and faster selection of models, more features
- read / erase / write Serial SPI memories likeMX25L160 , W25X32 and F-RAM eg. FM25L04
- RNS 315 original code reading the without the use of expander (procedures work independently without control computer)
- JTAG programmer (in development)
- in many cases, support K / L - Line without external power supply 12V
- K / L support in different voltage ranges from 1 to 15 V (programmable)
- 10 universal I / O lines with programmable logic from 1 to 5 V
- UART and RS232 (separate outputs for RS232 - a standard PC or signal level from -9V ..+ 9V )
- UART in logic from 0 to 15V - max voltage from 1V to 15V
- RS232 with the range of -12V .. +12V
- work on USB power + the ability to work on external power
- possibility to supply external circuits from the box
- Vreg - programmable voltage from 0.5 .. 5V (max voltage dependent on the performance of the computer USB)
- hardware and software support for most protocols OBD ( ALDL , OBD -I, OBD -1.5 , OBD-II , EOBD , EoBD2 , JOBD , ADR , SAE J1850 PWM , SAE J1850 VPW , ISO 9142-2)
- device is fully expandable, on the request of customers also
- programmable current protection outputs, IREG (sum of all outputs IO1 .. I08 + RX + TX)
- analog inputs - ADC-A, ADC-B
Box III specifications:
- diagnostic DB25 connector (inputs, outputs, TX232, RX232, CAN L, CAN H, K-Line, L-Line, Vreg, ADC-A, ADC-B)
- USB connector
- 9V external power supply connector
- 4 led diodes (BUSY/ERROR, CONNECTION, RX, TX)
- firmware update on the fly (in background, changes came after software close)
- drivers installations directly from windows update xp/vista/win7/win8/win8.1
For all Martech Clip users we have possibility to replace Clip into Box III (with moving activations from old to new device).
More details: shop@martech.pl.
Martech Box III
[Polski] [English]
[EN]
Why a new Box ?
Martech Clip is a device that already have more than 8 years (it was officially released in early 2006) supports hundreds of different radios and car navigation. So far we managed to "squeeze" more than was expected - for example flash memory reading by the JTAG protocol. The variety of processors, places where codes are stored forced us to use different interfaces (k-line), expanders (rcd210, rns315). By releasing Clip in 2006, we did not even think about car radio - our field was GSM in that times. Clip was in almost every service point across the world. Some models require more computing power, and most importantly - specific hardware, unfortunately - this could not be supported by Clip.With this in mind, the growing needs and requirements of our customers, we were forced to design a new device, which is Martech Box III.
Therefore, Martech Team introduces the most advanced equipment to service and repair of electronic equipment. Martech Box III.
Box III is an universal device which can find its application in such service sectors like:
radios and navigations
cars and all kinds of drivers, clusters
PC computers and laptops
RTV, AGD
different types of automation and robotics
Will you continue to support Clip ?
Yes, of course. Models that will be technically supported by the clip will be available in the updates.
The most Box III functions:
it's based on the latest STM32 processor, which provides stability and adequate speed
a number of safeguards against short circuits, faults caused by the user
hardware support for multiple interfaces
no need for additional adapters like Expander, pull-up resistors, K-Line interface
Box III supports communication over:
JTAG (np. LCN, RNS310, LSRNS, HSRNS, HSMCA)
OBD2 (OBD (K-Line, ALDL, OBD-I, OBD-1.5, OBD-II, EOBD, EoBD2, JOBD, ADR, SAE J1850 PWM, SAE J1850 VPW, ISO 9142-2)
UART (RS232, TX232, RNS510)
CAN L, CAN H, K-Line, L-Line, ADC-A, ADC-B
What's new in Box III, which is not on Clip so far:
Nissan LCN / Opel Corsa Touch & Connect (within the activation OMAP5948) original code reading
full support (read, write, erase) of M35080 3/6/V6/VP/D80/D160 (under the tab of programmer)
new user interface - easier and faster selection of models, more features
read / erase / write Serial SPI memories like 3MX25L160 , W25X2 and F-RAM eg. FM25L04
RNS 315 original code reading the without the use of expander (procedures work independently without control computer)
JTAG programmer (in development)
in many cases, support K / L - Line without external power supply 12V
K / L support in different voltage ranges from 1 to 15 V (programmable)
10 universal I / O lines with programmable logic from 1 to 5 V
UART and RS232 (separate outputs for RS232 - a standard PC or signal level from -9V ..+ 9V )
UART in logic from 0 to 15V - max voltage from 1V to 15V
RS232 with the range of -12V .. +12V
work on USB power + the ability to work on external power
possibility to supply external circuits from the box
Vreg - programmable voltage from 0.5 .. 5V (max voltage dependent on the performance of the computer USB)
hardware and software support for most protocols OBD ( ALDL , OBD -I, OBD -1.5 ,
OBD-II , EOBD , EoBD2 , JOBD , ADR , SAE J1850 PWM , SAE J1850 VPW , ISO 9142-2)
device is fully expandable, on the request of customers also
programmable current protection outputs, IREG (sum of all outputs IO1 .. I08 + RX + TX)
analog inputs - ADC-A, ADC-B
Various UART versions:
K-line level 1..15V (without external power supply, just from USB to 9V)
L-line level 1..15V (without external power supply, just from USB to 9V)
RS232 TX/RX in -9..+9V range
RX/TX outputs 1..5V (USB)
MBUS on TX output
MBUS na RX output
on universal outputs
MAUS BUS (for cancheck in BP radios)
New functions in Programmer bookmark:
Eeprom / Flash: serial spi, i2c (X24c00 also), microwire (rotated with auto pin finding), 77007MN, KKZ
NEC (more types, faster connection)
Motorola (new bootloaders for HC05/11, secured also)
ST92 (more stable of work, reading secured in future)
Renesas M16/M32 (possibility to read out some of secured versions)
JTAG - Box III as a JTAG programmer for many type of ARM 7/9
no file coding – all can be saved in pure binary file (.mbin file is supported too)
a possibility of setting Vreg voltage, Rise Time, IREG , reading speed
Box III specifications:
diagnostic DB25 connector (inputs, outputs, TX232, RX232, CAN L, CAN H, K-Line, L-Line, Vreg, ADC-A, ADC-B)
USB connector
9V external power supply connector
4 led diodes (BUSY/ERROR, CONNECTION, RX, TX)
firmware update on the fly (in background, changes came after software close)
drivers installations directly from windows update xp/vista/win7/win8/win8.1
Regards
Martech Team
Martech
Citiraj tekst
