Prikazivanje rezultata 1 do 6 od 6

Tema: Gd 900

  1. #1
    GSM Junior
    Clan br.
    6485
    Registrovan
    Jun 2007
    Lokacija
    bgd
    Godina
    46
    Br. postova
    12
    Hvala
    0
    Pohvaljen 1 put u 1 postu

    Gd 900

    Problem sa GD 900 posle zamene prednjeg panela.Prilikom poziva LCD je taman,proban flash,proban drugi prednji panel(touch),probana druga ploča.
    Ako ima ko predlog hvala

  2. #2
    GSM Guru Kole@Bg's Avatar
    Clan br.
    2962
    Registrovan
    Dec 2006
    Lokacija
    Beograd
    Godina
    37
    Br. postova
    211
    Hvala
    6
    Pohvaljen 8 puta u 7 postova
    The following procedure worked for me, but it's potentially dangerous, and could ruin your phone if you're not careful - YOU HAVE BEEN WARNED!

    1. On the phone keypad enter the following code: 1809#*900# to bring up the engineering settings menu.

    2. Scroll down to the entry called OTHERS and select it.

    3. Scroll down this menu to the entry called PROXIMITY and select it.

    4. You should see three options: Enable, Disable & Start Calibration

    5. Select Start Calibration - after a few seconds it will return a new figure (mine was 3627)

    6. BACK right out of the menu system, and make a test call - it should blank the screen when you hold it to your ear (or when you hold a finger near the sensor), but come back on again when you remove it.

    ili proveri da nisi ostetio ili prekrio necim senzor
    ako ti izbacuje rezultat u crvenoj boji nesto nije ok sa senzorom za svetlo

  3. Sledeci korisnici su rekli hvala Kole@Bg za ovaj koristan post:


  4. #3
    GSM Junior damba's Avatar
    Clan br.
    12491
    Registrovan
    Jul 2009
    Lokacija
    Tuzla BIH
    Br. postova
    16
    Hvala
    20
    Pohvaljen 6 puta u 5 postova
    Citiram Original postovao Kole@Bg Pogledaj post
    The following procedure worked for me, but it's potentially dangerous, and could ruin your phone if you're not careful - YOU HAVE BEEN WARNED!

    1. On the phone keypad enter the following code: 1809#*900# to bring up the engineering settings menu.

    2. Scroll down to the entry called OTHERS and select it.

    3. Scroll down this menu to the entry called PROXIMITY and select it.

    4. You should see three options: Enable, Disable & Start Calibration

    5. Select Start Calibration - after a few seconds it will return a new figure (mine was 3627)

    6. BACK right out of the menu system, and make a test call - it should blank the screen when you hold it to your ear (or when you hold a finger near the sensor), but come back on again when you remove it.

    ili proveri da nisi ostetio ili prekrio necim senzor
    ako ti izbacuje rezultat u crvenoj boji nesto nije ok sa senzorom za svetlo
    Ja imo takav problem nisam nista mijenjao ,nego covjek donijeo takav tel. (sve radi na tel.samo kad zoves ili kad tebe zovu zatamni se lcd) prije mjesec i rijesio na ovaj nacin !

  5. #4
    GSM Junior
    Clan br.
    6485
    Registrovan
    Jun 2007
    Lokacija
    bgd
    Godina
    46
    Br. postova
    12
    Hvala
    0
    Pohvaljen 1 put u 1 postu
    hvala braćo,javim asutra šta je bilo

  6. #5
    Balkan GSM Team Eprom's Avatar
    Clan br.
    487
    Registrovan
    Dec 2005
    Lokacija
    Srbija,Zemun,Bezanijska 18 service,Bezanijska 21 battery shop
    Godina
    51
    Br. postova
    6.474
    Hvala
    1.243
    Pohvaljen 1.577 puta u 891 postova
    Citiram Original postovao brdo Pogledaj post
    hvala braćo,javim asutra šta je bilo
    Jel vi to radite jednom sedmicno ili je ono bila sala za 01.04

  7. #6
    GSM Junior
    Clan br.
    6485
    Registrovan
    Jun 2007
    Lokacija
    bgd
    Godina
    46
    Br. postova
    12
    Hvala
    0
    Pohvaljen 1 put u 1 postu
    Hvala bio je senzor,osto mi poklopac na masci.Pozdrav
    A ti eprome ne smari ,već radi te nešto

Pravila postovanja

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •