Prikazivanje rezultata 1 do 3 od 3

Tema: *** Cyclone Box Pinouts ***

  1. #1
    Balkan GSM Team Rem@x's Avatar
    Clan br.
    58
    Registrovan
    Sep 2005
    Lokacija
    Tuzla,B & H
    Godina
    42
    Br. postova
    868
    Hvala
    14
    Pohvaljen 73 puta u 53 postova

    *** Cyclone Box Pinouts ***

    SERVICE socket
    (10 pin layout)
    1 - BOX GENIO1
    2 - VBAT (5v)
    3 - BOX GENIO2
    4 - BSI
    5 - BOX RX_1
    6 - BOX TX_1
    7 - MBUS
    8 - GND
    9 - VPP
    10 - BOX GENIO3

    As you can see, pinout is compatible with UFS/JAF and other common Nokia boxes. For DCT4 you can plug directly UFS/JAF cables without any adapter. With BB5, most 8-pin market cables have TX2 instead VPP Pin. Our box don't have connected data line to VPP - only to power IC.
    Tx2 might be changed ON THE FLY to any of GENIO pins (in further updated maybe also possible 100% flexible pinout modification, so ALL cables on markets will be supported!).
    Bundled adapter crossing pin 3 with 9. That means on output from adapter, on pin 8 you will have TX2 (service pin 3) and still compatibility with UFS/JAF cables will be. VPP is not cutted. It's on pin nr 3 (unused pin nr 2 - jaf/ufs cables) so still VPP funcionality can be used on 8 pin cables, instead of purchasing 10 pin! With small mods needed, of course.
    You can use too native 10pin Cyclone cables, but they are not avaiable on market at moment.


    DIAGNOSTIC socket
    1 - VBAT (5v)
    2 - USART CLK
    3 - USART TXD
    4 - FREQ_MEASURMENT_A0
    5 - FREQ_MEASURMENT_CLK
    6 - DIAG_1_VOLTMETER
    7 - DIAG_2_VOLTMETER
    8 - DIAG_3_VOLTMETER
    9 - USART RXD
    10 - GND

  2. #2
    Balkan GSM Team Rem@x's Avatar
    Clan br.
    58
    Registrovan
    Sep 2005
    Lokacija
    Tuzla,B & H
    Godina
    42
    Br. postova
    868
    Hvala
    14
    Pohvaljen 73 puta u 53 postova
    *** Cyclone Box and VPP thing ***
    As almost each unlocker know, VPP is used to boost flash erase and store time.
    It's common used for older NOR phones (in latest NAND/ONENAND, they are fast enough without VPP).
    Before flashing phone with VPP make sure your cable have VPP connected to PIN 8 (or pin 9 on 10pin layout or pin 3 with adapter).
    Now there is 2 boosting options:

    1. Box can either supply own, internal generated VPP signal, but only 5v. So you need attach VPP Pump, then 9V will appear on output, and flashing will be boosted.
    2. Box can supply native VPP signal. But correct DC power supply needs be applied. 10v should be enough (input diode resulting in voltage drop - about 0,6V + power IC also dropping some, so keep note that), programming not taking a much current so 100-500mA will be very fine (of course more will not do any damage).
    You can check output voltage by running box selftest, so you can ensure you will kill or not kill your flash chip. As long as power supply manufacturers sometime likes to make some jokes

  3. #3
    Balkan GSM Team Rem@x's Avatar
    Clan br.
    58
    Registrovan
    Sep 2005
    Lokacija
    Tuzla,B & H
    Godina
    42
    Br. postova
    868
    Hvala
    14
    Pohvaljen 73 puta u 53 postova
    ** Before BB5 USB Flashing **
    Keep note, that before proceeding with BB5 USB Flash (either alive or dead) FLASH IMAGES have to be added on list!
    Otherwise it will FAIL !

Slicne teme

  1. Martech Box II to Box II Plus EXCHANGE OFFER
    Postovao YuMERA u forumu Martech
    Odgovori: 10
    Zadnji post: 13-05-09, 13:57
  2. Gde nabaviti CYCLONE box
    Postovao woodoo u forumu HW oprema
    Odgovori: 9
    Zadnji post: 04-05-09, 23:32
  3. Nekoliko zica trazim
    Postovao Amaro u forumu Potraznja
    Odgovori: 6
    Zadnji post: 09-02-09, 14:11
  4. 24.05.2006 - ALCATEL servisni softver za MT box
    Postovao SoftMobile u forumu MT Nokia
    Odgovori: 5
    Zadnji post: 15-02-08, 23:49

Pravila postovanja

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •