Prikazivanje rezultata 1 do 16 od 16

Tema: Problem sa instalacijom boxa

  1. #1
    GSM Junior tonimontana's Avatar
    Clan br.
    9121
    Registrovan
    Nov 2007
    Lokacija
    uzice
    Br. postova
    16
    Hvala
    0
    Pohvaljen 0 puta u 0 postova

    Problem sa instalacijom boxa

    Kad ga ubodem na USB, upali se samo PWR lampica, PC ne pronalazi novi hardware. Da li mi nesto nije u redu sa boxom, posto sam to probao i na drugom PC-iju i isto pokazuje.

  2. #2
    Balkan GSM Team Code Electronic's Avatar
    Clan br.
    295
    Registrovan
    Nov 2005
    Lokacija
    Code Support
    Br. postova
    583
    Hvala
    0
    Pohvaljen 0 puta u 0 postova
    nisi dobro drivere instalirao

    evo ti link za sve sto ti je potrebno > http://67.15.15.218/BB5_box_by_DK/

  3. #3
    Product Suporter Dr.Nele's Avatar
    Clan br.
    95
    Registrovan
    Oct 2005
    Lokacija
    Добој, Цара Душана 49
    Br. postova
    1.666
    Hvala
    434
    Pohvaljen 546 puta u 312 postova
    Vidi kako ga vidi racunar, prepoznao ga je pod nesto drugo? Imas ovdje objasnjeno sta i kako.

    http://www.bb5.hk/Support.html

    @code
    Bio si brzi

  4. #4
    GSM Junior tonimontana's Avatar
    Clan br.
    9121
    Registrovan
    Nov 2007
    Lokacija
    uzice
    Br. postova
    16
    Hvala
    0
    Pohvaljen 0 puta u 0 postova
    Prerovio sam sve po device manageru , na com portevima imam samo (com1), (com2), i lpt, nema ga nigde.

  5. #5
    Product Suporter Dr.Nele's Avatar
    Clan br.
    95
    Registrovan
    Oct 2005
    Lokacija
    Добој, Цара Душана 49
    Br. postova
    1.666
    Hvala
    434
    Pohvaljen 546 puta u 312 postova
    Pozovi nekoga ko malo vise zna o tome od tebe, dovoljno si rekao za danas.

  6. #6
    GSM Junior tonimontana's Avatar
    Clan br.
    9121
    Registrovan
    Nov 2007
    Lokacija
    uzice
    Br. postova
    16
    Hvala
    0
    Pohvaljen 0 puta u 0 postova
    Sta sam pogresno rekao, trebalo bi da ga prepozna u portevima, nema ga ni na USB controlerima, nigde ga ne prepoznaje.TJ ne vidi ga PC, nista novo ne prepoznaje kad ga ubodem, samo box upali, PWR lampicu.

  7. #7
    Balkan GSM Team Eprom's Avatar
    Clan br.
    487
    Registrovan
    Dec 2005
    Lokacija
    Srbija,Zemun,Bezanijska 18 service,Bezanijska 21 battery shop
    Godina
    52
    Br. postova
    6.474
    Hvala
    1.243
    Pohvaljen 1.580 puta u 892 postova
    Citiram Original postovao tonimontana Pogledaj post
    Sta sam pogresno rekao, trebalo bi da ga prepozna u portevima, nema ga ni na USB controlerima, nigde ga ne prepoznaje.TJ ne vidi ga PC, nista novo ne prepoznaje kad ga ubodem, samo box upali, PWR lampicu.
    Obrisi sve instaliraj sa support-a pa onda ubodi box i obavezno mora da bude ispod 10-tog porta!I nek je sa srecom samo napred resices ti to

    b/r Andrija

  8. #8
    GSM Master rama's Avatar
    Clan br.
    545
    Registrovan
    Dec 2005
    Lokacija
    Ruma
    Godina
    49
    Br. postova
    657
    Hvala
    147
    Pohvaljen 249 puta u 88 postova
    Citiram Original postovao tonimontana Pogledaj post
    Sta sam pogresno rekao, trebalo bi da ga prepozna u portevima, nema ga ni na USB controlerima, nigde ga ne prepoznaje.TJ ne vidi ga PC, nista novo ne prepoznaje kad ga ubodem, samo box upali, PWR lampicu.
    nista lose nisi rekao covek ti je dao link pa pogledaj,da neces da dodje neko i da ti instalira mozda

  9. #9
    Banned aga's Avatar
    Clan br.
    1618
    Registrovan
    Jun 2006
    Lokacija
    Sarajevo
    Godina
    48
    Br. postova
    247
    Hvala
    0
    Pohvaljen 0 puta u 0 postova
    1. Copy and paste bb5_unlocker folder to C:/ drive
    2. Open bb5_unlocker folder and run install.bat
    3. After install finished, message will appear "bb5 box not found", press ok
    4. Connect box to usb port on computer
    5. Windows will ask for driver, browse to folder "bb5_unlocker" -> "winxp dejan", and let windows install drivers
    6. Go to Device Manager
    7. Go to Ports (COM & LPT)
    8. right-click on dejan bb5 box and go to properties
    9. change com port to lowest possible (port 2)
    10. click on scan for hardware changes
    11. click ok
    12. open bb5unlocker sw
    13. connect cable to box
    14. open phone
    15. connect positive (red connector) to 1st pin (left) of batt connector
    16. connect bsi (yellow connector) to 2nd pin (middle) of batt connector --> NOT need for 6280
    17. connect GND (black crocodile clip) to vibrator. for 6131 need to connect to pop port connector of phone
    18. connect cable to phone connector
    19. power up phone
    20. click on read info on sw
    21. phone info will appear with lock status
    22. if try 1 = 2,3,4,10 or any number, this has no affect (this is wrong unlock by code)
    23. if try 2 = 10, then phone CANNOT be unlocked (this is wrong unlock by fbus). if counter is 0, then after unlocking
    or wrong unlock a backup is autmatically stored in backup folder in bb5_unlocker folder. everytime after a wrong
    unlock (usually by touching other pins on rap ic, and therefore causing the phone to switch off, then sw cant read
    and error will appear on screen) then counter will increase, if goes up to 4 or 6 then you must press
    "write backup" to reset counter.
    24. CLK = CLOCK = small tp
    25. AD1 = DATA = big tp with unlock ignition switch
    26. connect tp's on top of pins shown on tp photo, lightly %%%%%ng down the spring loaded pins of tp connectors down on
    tp pins, only slightly, just touching, otherwise rap3g ic will damage
    27. just click ignition button on DATA tp, keeping tp connectors connected to pins
    28. phone will unlock within 3-5 secs and will show unlock successful message
    29. if message appears: cannot unlock phone! - this means tp pins you connected are incorrect or lost connection,
    then take out rj45 cable out from box and put back, then switch on phone again and repeat procedure.

  10. #10
    GSM Guru Nikola's Avatar
    Clan br.
    300
    Registrovan
    Nov 2005
    Lokacija
    JASKA-vino
    Br. postova
    164
    Hvala
    0
    Pohvaljen 0 puta u 0 postova
    Citiram Original postovao aga Pogledaj post
    1. Copy and paste bb5_unlocker folder to C:/ drive
    2. Open bb5_unlocker folder and run install.bat
    3. After install finished, message will appear "bb5 box not found", press ok
    4. Connect box to usb port on computer
    5. Windows will ask for driver, browse to folder "bb5_unlocker" -> "winxp dejan", and let windows install drivers
    6. Go to Device Manager
    7. Go to Ports (COM & LPT)
    8. right-click on dejan bb5 box and go to properties
    9. change com port to lowest possible (port 2)
    10. click on scan for hardware changes
    11. click ok
    12. open bb5unlocker sw
    13. connect cable to box
    14. open phone
    15. connect positive (red connector) to 1st pin (left) of batt connector
    16. connect bsi (yellow connector) to 2nd pin (middle) of batt connector --> NOT need for 6280
    17. connect GND (black crocodile clip) to vibrator. for 6131 need to connect to pop port connector of phone
    18. connect cable to phone connector
    19. power up phone
    20. click on read info on sw
    21. phone info will appear with lock status
    22. if try 1 = 2,3,4,10 or any number, this has no affect (this is wrong unlock by code)
    23. if try 2 = 10, then phone CANNOT be unlocked (this is wrong unlock by fbus). if counter is 0, then after unlocking
    or wrong unlock a backup is autmatically stored in backup folder in bb5_unlocker folder. everytime after a wrong
    unlock (usually by touching other pins on rap ic, and therefore causing the phone to switch off, then sw cant read
    and error will appear on screen) then counter will increase, if goes up to 4 or 6 then you must press
    "write backup" to reset counter.
    24. CLK = CLOCK = small tp
    25. AD1 = DATA = big tp with unlock ignition switch
    26. connect tp's on top of pins shown on tp photo, lightly %%%%%ng down the spring loaded pins of tp connectors down on
    tp pins, only slightly, just touching, otherwise rap3g ic will damage
    27. just click ignition button on DATA tp, keeping tp connectors connected to pins
    28. phone will unlock within 3-5 secs and will show unlock successful message
    29. if message appears: cannot unlock phone! - this means tp pins you connected are incorrect or lost connection,
    then take out rj45 cable out from box and put back, then switch on phone again and repeat procedure.
    auuuu majstore sta tebe napade ?
    aal se raspiso ili copy paste?
    al svejedno ga ima

  11. #11
    GSM Junior tonimontana's Avatar
    Clan br.
    9121
    Registrovan
    Nov 2007
    Lokacija
    uzice
    Br. postova
    16
    Hvala
    0
    Pohvaljen 0 puta u 0 postova
    Ok, hvala na pomoci, nije uopste problem u tome da ne umem da ga instaliram izgleda da je box mrtav, uopste ga ne nalazi nijedan racunar, kad se nakaci na PC ne pali mu se USB lampica, vec samo PWR, tj racunar ne prepoznaje novi hardware kao sto bi trebalo i ne gore mu sve lampice koje bi trebale kad se ovaj box nakaci na USB.Pogledao sam da se nije slucajno odlemio USB na boxu al sve je OK.100% sam siguran da box nije u redu jer sam vec instalirao par komada drugim ljudima. Nego me interesuje da nije neko imao ovakvo iskustvo, vraticu neispravan box i problem resen.Ako neko moze da mi kaze dal treba da mu gori PWR i USB led kad se nakaci na PC ?

  12. #12
    Balkan GSM Team Eprom's Avatar
    Clan br.
    487
    Registrovan
    Dec 2005
    Lokacija
    Srbija,Zemun,Bezanijska 18 service,Bezanijska 21 battery shop
    Godina
    52
    Br. postova
    6.474
    Hvala
    1.243
    Pohvaljen 1.580 puta u 892 postova
    Citiram Original postovao tonimontana Pogledaj post
    Ok, hvala na pomoci, nije uopste problem u tome da ne umem da ga instaliram izgleda da je box mrtav, uopste ga ne nalazi nijedan racunar, kad se nakaci na PC ne pali mu se USB lampica, vec samo PWR, tj racunar ne prepoznaje novi hardware kao sto bi trebalo i ne gore mu sve lampice koje bi trebale kad se ovaj box nakaci na USB.Pogledao sam da se nije slucajno odlemio USB na boxu al sve je OK.100% sam siguran da box nije u redu jer sam vec instalirao par komada drugim ljudima. Nego me interesuje da nije neko imao ovakvo iskustvo, vraticu neispravan box i problem resen.Ako neko moze da mi kaze dal treba da mu gori PWR i USB led kad se nakaci na PC ?

    Nema zaista potrebe da ti bilo sta vise pricamo.Ti rece da si vec instalirao drugima par komada pa onda i znas da li i koje treba da svetle/gore lampice.Taj je neispravan i vracas ga zato nemoj vise da nam oduzimas vremena dovoljno si vec oduzeo.

    b/r Andrija

  13. #13
    GSM Master digico's Avatar
    Clan br.
    2869
    Registrovan
    Nov 2006
    Lokacija
    www.digico.com.mk
    Godina
    43
    Br. postova
    466
    Hvala
    2
    Pohvaljen 4 puta u 2 postova
    @toni
    Ma nesekiraj se druze. Nece ti jos mnogo trebati sudeci po najnoviim desavkama a ako ti toliko drag imam jedan na prodaju

  14. #14
    GSM Master mobicom's Avatar
    Clan br.
    927
    Registrovan
    Mar 2006
    Lokacija
    Tetovo, MK +42� 0' 27.37", +20� 58' 38.51"
    Br. postova
    705
    Hvala
    69
    Pohvaljen 45 puta u 27 postova
    usb ga odma pronalazi i na popup info ti napise da se radi o DK box-u, zao mi je ali mislim da imas ne ispravan box.Ako onaj ko ti prodao dozvoljava da ga otvoris onda ga otvori i prelemi malo, nije nista komplikovano.

    pozdrav.

    @skupino
    Vi ste poceli vise sa svakim da se zezate samo cekate zrtvu.

  15. #15
    Product Suporter cacko's Avatar
    Clan br.
    1853
    Registrovan
    Jul 2006
    Lokacija
    Macedonia,Kumanovo
    Godina
    35
    Br. postova
    283
    Hvala
    17
    Pohvaljen 14 puta u 7 postova
    Citiram Original postovao mobicom Pogledaj post

    @skupino
    Vi ste poceli vise sa svakim da se zezate samo cekate zrtvu.
    Pa tako i treba,vidimo da covek ne pita o UFS kao svaki drugi ,nego covek za pocetak uzeo BB5.......


    Pozdrav

  16. #16
    GSM Junior tonimontana's Avatar
    Clan br.
    9121
    Registrovan
    Nov 2007
    Lokacija
    uzice
    Br. postova
    16
    Hvala
    0
    Pohvaljen 0 puta u 0 postova
    Citiram Original postovao Eprom Pogledaj post
    Nema zaista potrebe da ti bilo sta vise pricamo.Ti rece da si vec instalirao drugima par komada pa onda i znas da li i koje treba da svetle/gore lampice.Taj je neispravan i vracas ga zato nemoj vise da nam oduzimas vremena dovoljno si vec oduzeo.

    b/r Andrija
    IZVINI,ovo je slobodna zemlja kao i forum, ako neko ima viska vremena pomocice mi, TEBI LICNO IZVINI. Ljudi smo nismo na nozu, pozz svima.
    Izmenio tonimontana : 29-01-08 u 12:04

Slicne teme

  1. ULT problem s instalacijom!!!!!!!!!!!
    Postovao pArAziT u forumu ULT Pro
    Odgovori: 1
    Zadnji post: 02-04-08, 18:16
  2. Problem s instalacijom setool 3 boxa
    Postovao sopiko u forumu SEtool support forum
    Odgovori: 17
    Zadnji post: 31-03-08, 16:17
  3. problem sa instalacijom z240 trebam drajvere
    Postovao mmanduri u forumu M46 i starije serije
    Odgovori: 6
    Zadnji post: 04-12-07, 14:28
  4. problem with new dongle
    Postovao sorinm u forumu J.A.F.
    Odgovori: 16
    Zadnji post: 10-07-07, 23:15
  5. problem sa instalacijom
    Postovao orao u forumu UST Pro II
    Odgovori: 2
    Zadnji post: 31-03-07, 20:16

Pravila postovanja

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •